作业帮数控车椭圆宏程序用的FANUC系统,O1000;M03S600T0101;G00X50.Z2.;#1=0#2=-47.159(椭圆终点)WHILE[#1GE#2]DO1#3=#1+30.0#4=24*SQRT[1-#3*#3/[30*30]]G01X[2*[#4]]Z[#1]#1=#1-0.1END1G00X50Z2M30就这个椭圆的宏程序,老是提示在WHILE那段
来源：学生作业帮助网 编辑：作业帮 时间：2024/12/02 08:08:44
![数控车椭圆宏程序用的FANUC系统,O1000;M03S600T0101;G00X50.Z2.;#1=0#2=-47.159(椭圆终点)WHILE[#1GE#2]DO1#3=#1+30.0#4=24*SQRT[1-#3*#3/[30*30]]G01X[2*[#4]]Z[#1]#1=#1-0.1END1G00X50Z2M30就这个椭圆的宏程序,老是提示在WHILE那段](/uploads/image/z/3283923-3-3.jpg?t=%E6%95%B0%E6%8E%A7%E8%BD%A6%E6%A4%AD%E5%9C%86%E5%AE%8F%E7%A8%8B%E5%BA%8F%E7%94%A8%E7%9A%84FANUC%E7%B3%BB%E7%BB%9F%2CO1000%3BM03S600T0101%3BG00X50.Z2.%3B%231%3D0%232%3D-47.159%28%E6%A4%AD%E5%9C%86%E7%BB%88%E7%82%B9%29WHILE%5B%231GE%232%5DDO1%233%3D%231%2B30.0%234%3D24%2ASQRT%5B1-%233%2A%233%2F%5B30%2A30%5D%5DG01X%5B2%2A%5B%234%5D%5DZ%5B%231%5D%231%3D%231-0.1END1G00X50Z2M30%E5%B0%B1%E8%BF%99%E4%B8%AA%E6%A4%AD%E5%9C%86%E7%9A%84%E5%AE%8F%E7%A8%8B%E5%BA%8F%2C%E8%80%81%E6%98%AF%E6%8F%90%E7%A4%BA%E5%9C%A8WHILE%E9%82%A3%E6%AE%B5)
数控车椭圆宏程序用的FANUC系统,O1000;M03S600T0101;G00X50.Z2.;#1=0#2=-47.159(椭圆终点)WHILE[#1GE#2]DO1#3=#1+30.0#4=24*SQRT[1-#3*#3/[30*30]]G01X[2*[#4]]Z[#1]#1=#1-0.1END1G00X50Z2M30就这个椭圆的宏程序,老是提示在WHILE那段
数控车椭圆宏程序
用的FANUC系统,
O1000;
M03S600T0101;
G00X50.Z2.;
#1=0
#2=-47.159(椭圆终点)
WHILE[#1GE#2]DO1
#3=#1+30.0
#4=24*SQRT[1-#3*#3/[30*30]]
G01X[2*[#4]]Z[#1]
#1=#1-0.1
END1
G00X50
Z2
M30
就这个椭圆的宏程序,老是提示在WHILE那段出现死循环.椭圆长轴30短轴24
数控车椭圆宏程序用的FANUC系统,O1000;M03S600T0101;G00X50.Z2.;#1=0#2=-47.159(椭圆终点)WHILE[#1GE#2]DO1#3=#1+30.0#4=24*SQRT[1-#3*#3/[30*30]]G01X[2*[#4]]Z[#1]#1=#1-0.1END1G00X50Z2M30就这个椭圆的宏程序,老是提示在WHILE那段
O1000;
M3 S600;
T0101;
G00 X0 Z150
G98
#24=80(短轴半径,X轴方向)
#26=100(长轴半径,Z轴方向)
#7=0.1
#1=#26+#7(Z轴方向最大值,假设为顶点)
#23=3.15(Z轴方向最小值)
WHILE[#1GT#23]DO1
#1=#1+#7(计算每次Z轴的坐标值)
IF[#1GT#23]GOTO9
#1=#23(最后一次把Z轴终点坐标赋值给#1)
N9 #3=2*#24*SQRT[1-[#1*#1]/[#26*#26]](X轴坐标值计算,此处按直径编程)
G01 X#3 Z#1 F100
END1
M30